Browse All Products
Solid Oak Flat Strip
Solid Oak Flat Strip is designed to cover the expansion gap. It also can be used as any transition, or as a door threshold. *As all of our thresholds are natural solid oak products, this means the grain and colour may vary.
£4.49 - £31.39
Duralay Timbermate Excel Wood/Laminate Flooring Underlay 3.6mm
Duralay Timbermate Excel is part of the Timbermate Range of superior underlays perfectly designed for the installation of engineered wood flooring and laminate flooring . Timbermate Excel reduces in-room noise by up to 30% and contains a Vapourstop barrier to help prevent moisture. Independently tested to produce a sound reduction rating of 56 SONE 3.60mm gauge high density resilient rubber underlay 0.55 Tog rating 23db sound insulation High density sponge material Vapourstop barrier that helps prevent moisture Prevents the overstraining of wood and laminate boards Suitable for use on most subfloor types including screed and suspended timber floors Provides an excellent sub-floor masking minor surface imperfections Simple, quick and easy to install It’s recommended for the joints to be taped together, we recommend our vapour tape. Available as the full size 11m x 1.37m (15.07m2) roll and the 14.6m x 0.685m (10m2) DIY Roll What is the difference between Timbermate Excel and Silentfloor Gold? Timbermate Excel is a 3.60mm gauge high density resilient rubber underlay; while the premium product in the Timbermate range, Silentfloor Gold is a 4.3mm gauge high density resilient rubber underlay, with the lowest Sone rating in the range.
£63.50 - £80.53
Solid Oak Ramp Threshold
These solid oak flooring trim profiles are available with 7mm, 15mm and 20mm rebates. Designed to create a smooth transition between wooden floors and floors of a different height. Most commonly used to link wood to wood, wood to tile, wood to vinyl and wood to carpet. Solid oak moulding Reducer to bridge variations in height between two floors Suitable for solid, engineered and laminate wood floors Unfinished allows for good colour match to the flooring finish Lacquered finish saves time, looks great and is ready to fit Quick and easy installation *As all of our thresholds are natural real solid oak products, this means the grain and colour may vary.
£3.26 - £58.38
White Laminate Scotia - 15mm x 15mm - 2.4m - Pack of 10
Provides the finishing edge to wood flooring by covering expansion gaps between the floor and the wall. Pack of 10 - 2.4m lengths. Single units available in store only.
£4.49 - £34.55
T-Section - Solid Oak Thresholds
This extra wide solid oak flooring profile is ideal for a flat transition between two floors of the same height. It can be used to link wood to wood, wood to tile or wood to carpet. Solid oak moulding A T-bar joining two floors of the same height Suitable for 14mm, 15mm, 18mm and 20mm solid and engineered wood floors Unfinished allows for good colour match to the flooring finish Lacquered finish saves time, looks great and is ready to fit Quick and easy installation *As all of our thresholds are natural solid oak products, this means the grain and colour tones may vary.
£4.49 - £53.16
L-Section - Solid Oak Threshold
Solid oak threshold commonly known as end section or L-section. Available with a 7mm, 15mm and 20mm rebate. Popular uses include to go against patio doors, UPVC doors and to edge coir matting. Solid oak moulding Suitable for solid and engineered wood floors Unfinished allows for good colour match to the flooring finish Lacquered finish saves time, looks great and is ready to fit Quick and easy installation *As all of our thresholds are natural real solid oak products, this means the grain and colour may vary.
£4.49 - £46.60
Bona R848 Flexible Wood Flooring Adhesive 15Kg
Bona R848 is an elastic, 1-component silane wood floor adhesive. A high performance formulation that is ideal for the installation of engineered wood flooring including engineered parquet flooring. Can also be used for solid boards up to 190mm wide.KEY BENEFITS Easy to apply Fast initial bonding strength Allows load after 24 hours Up to two years' shelf life Great rib stability Compatible with underfloor heating Coverage dependant on trowel used 850 - 1250G Tensions to the sub floor are reduced. The adhesive hardens by a chemical reaction with moisture. Suitable subfloors; timber and screed Cementitious screed (CT) according to EN 13813 Floors levelled with levelling compounds (at least 2 mm thick, resistant against plasticizer migration) Calcium sulfate screed (CA) according to EN 13813 Chipboard V100 Other dry and sound sub floors Floor Preparation Subfloor preparation should be in accordance with British Standard.
£99.98
Wood To Carpet - Solid Oak Reducer Threshold
This floor profile is designed to bridge the gap between your new floor and existing floor. When you meet a lower height than your new floor you may need to adapt the trim slightly to fit the height of your existing floor. This reducer is also designed to connect a room with wood flooring to a room with carpet. *As all of our thresholds are natural solid oak products, this means the grain and colour may vary.
£4.49 - £53.16
Osmo Wash and Care
Osmo Wash and Care cleaner is a specially formulated wood cleaner suitable for cleaning and maintaining oil and wax finishes. Its pH balanced formula quickly and effectively cleans wooden flooring, furniture, doors, wall and ceiling panels to leave a streak free finish. Application SURFACE PREPARATION To remove loose debris, we recommend using Osmo Dust-Mop, a conventional vacuum cleaner or broom. METHOD OF APPLICATION Manual: Wash and Care is ideally used with Osmo Micro-Mop Plush. Add Osmo Wash and Care to water. Clean the floor with a damp (not wet) mop and wipe dry immediately. When applied regularly, the surface becomes resistant to dirt and wear. Machine: Spread the diluted Wash and Care solution with a pump sprayer. Loosen dirt with a single disc machine, e.g. Osmo FloorXcenter, and a white pad.Immediately, mop away or remove with a round Osmo Microfibre Pad for machines. NOTE To specifically remove especially tough stains and to occasionally, intensively refresh waxed or oiled floors, we recommend using our tried and trusted Osmo Liquid Wax Cleaner, which is based on natural plant oils and waxes (undiluted application with Osmo Active Fibre Cloth).For a complete renovation, we recommend an Osmo Polyx®-Oil.
£18.34 - £67.73
Bona Adhesive Glue Trowels
For the application of Bona adhesives. Fine (F) and coarse (G) versions available in each size.
£10.20
Osmo Natural Bristle Brush
The Osmo Soft Tip Brush is ideal for applying the range of Osmo wood oils.Looking for a different type of brush? See the full range of Osmo brushesThis product can also be found as part of the Osmo Premium Roller and Osmo Brush Set and the Osmo Decking Brush SetPreparationAs a general rule, we recommend that surfaces should be clean and dry, and that all traces of dust and dirt be removed with a broom or vacuum cleaner before applying a wood finish.The necessity of sanding and removing previous finishes from the surface to be worked on will depend on the oil, wax or varnish used (see product instructions for guidance on this).ApplicationSimply dip your Osmo Soft Tip Brush into the oil or other product you are using, being careful not to overfill it, then brush evenly along the wood grainAny surplus should be removed immediately with a microfibre clothApply second coat of oil with the Osmo Oil Finish Application Fleece and remove excessAftercareOsmo Brush Cleaner and Thinner has been designed specifically for cleaning brushes which have been used to apply Osmo wood oils.Features and Highlights A high quality soft tip brush for the application of wood oils Ideal for both professional and DIY use Flat, straight edge construction, perfect for corners and edging Ergonomic wooden handle for comfort and durability Sturdy metal bristle brace reduces bristle loss during application Bristles are made from a high quality synthetic mix for a perfect finish every time
£6.24 - £15.17
Osmo Polyx-Oil Original
Osmo Polyx-Oil Original 3032 and 3062 is a protective wood treatment for interior use. Combines natural oils and waxes to form a hardwearing and durable finish which is ideal for wooden flooring and furniture. Osmo Polyx Hardwax Oil provides a warm and rich effect that brings out the true beauty of all woods by emphasising the grain and promoting its natural characteristics. Exceptional durability is achieved. Microporous and will not crack, flake or peel. Key Features Resistant to common household spillages Application is by brush or roller Coverage up to 24sq/m per litre Touch dry between 4-8 hours and recoatable after 12 hours. Recommended 2 coats Application SURFACE PREPARATION Wood surface must be clean, dry and frost-free (moisture content max. 18%).Osmo Polyx®-Oil Original is ready to use. Do not thin. Stir well using a flat stirring stick or spatula before use. Clean old microporous stains thoroughly. Old paints and lacquers must be completely removed. As a general rule, wear a dust mask during sanding works. Fill small cracks, larger joints or holes in wood (with Osmo Wood Filler).Sand wood surfaces carefully. Begin with coarse sandpaper – final sanding work for flooring P120-150, for furniture P180-240. Before oiling the surface, remove sanding dust with a broom or vacuum.The finished surface is influenced by several factors, including the condition of the wood. Therefore, a trial application is always required, especially for unfamiliar surfaces. METHOD OF APPLICATION With Osmo Flat Brush, Floor Brush, Oil Finish Applicator Fleece (Hand Pad Holder) or Osmo Microfibre Roller, apply thinly along the wood grain and spread well. Allow to dry for approx. 8-10 hours under good ventilation.After drying, quickly apply a second coat also thinly. After 2-3 weeks, the surface is fully cured. When renovating or recoating an already oiled surface, one coat applied to the clean and dry surface is usually sufficient. NOTE Oils enhance the natural tone of wood (permanent wet effect). Applying the product too generously and insufficient ventilation lead to delays in drying.For dark and extractive-rich hardwoods (e.g. Wenge, Merbau, Jatoba etc.), we recommend using Osmo Wood Wax Finish Clear Extra Thin. A trial application is recommended.For cork surfaces, due to their high absorbency please ensure that the wood finish is applied especially thinly.On cork, longer drying times are to be taken into consideration (at least 24 hours).Caution: Apply max. one coat thinly to cabinet interiors and drawers with a cloth. If a higher gloss level is desired use Osmo Liquid Wax Cleaner very thinly and polish when dry. Avoid using Osmo Liquid Wax Cleaner on surfaces that have not dried and cured properly. Always trial apply first. Using general or multi-purpose cleaners will increase the frequency of maintenance and recoating. Allow finish to fully cure before heavy usage. CARE Regular Cleaning: Wood surfaces treated with Polyx®-Oil are highly repellent and easy to maintain. Remove debris with the Osmo green Dust-Mop from the Mop Cleaning Kit for Floors, or use a broom or a vacuum cleaner.Damp mop floors using diluted Osmo Wash and Care and the Osmo Micro-Mop Plush from the Mop Cleaning Kit for Floors. Avoid saturating the surface with water. For the convenient cleaning of floors use Osmo Spray-Mop. For furniture or small areas, use Osmo Spray Cleaner and Osmo Easy Pads. Occasional Maintenance: For spot cleaning stubborn scuff marks, or occasionally refreshing satin or gloss Polyx-Oils use Osmo Liquid Wax Cleaner. Alternatively, Osmo Maintenance Oils can be used to occasionally refresh most Polyx Oil sheen levels, including matt. Ensure surfaces are appropriately cleaned before thinly applying Osmo Maintenance Oils. Recoating: Simply re-apply one coat onto the appropriately cleaned and dried surface when signs of wear become visible.
£3.99 - £96.72
Osmo MS Trade Flexible Wood Flooring Adhesive 15kg
OSMOUK MS Trade is a one component adhesive specially formulated for the interior installation of parquet block, engineered wood plank as well as pre-finished and unfinished solid wood flooring. Solvent and isocyanate free, with negligible VOC content and low odour. Thanks to the special formulation the adhesive has great early strength build for immediate grab and quickly builds to a tenacious but elastic bond as the adhesive continues to cure. Specifications Approx. coverage: up to 18m² Application climate: 15-30°C, 30-60% RH Size: 15KG Suitable for use with under floor heating 100% solids and low odour Water and solvent free Isocyanate free High strength Waterproof bond Early quick grab Meets environmental emissions according to DIBt
£84.99£82.11
Refina HD Board & Floor Rules 1m - 3m (New)
Refina high quality aluminium straight edge, essential for levelling any plaster or render surface and helps identify hollows and high spots before sponging and trowelling up. Key features Straight edge & screed rule Heavy duty aluminium box section Capped ends Helps identify hollows and high spots in walls and floors sizes 3'4x3" (1000x80x40mm) 5'0x3" (1500x80x40mm) 6'8x3" (2000x80x40mm) 8'2x3" (2500x80x40mm) 10'0x3" (3000x80x40mm) Application For levelling & ruling off Plaster & render Floors & walls
£37.30 - £82.16
Pine Slivers - 6mm/8mm - 1m Lengths - Pack of 100
Our Pine Slivers are hand cut from reclaimed pine floorboards and pre-cut into convenient tapered wedges. They are perfect for gap filling between pine floorboards. Approximately 100 per pack Average 1m lengths See more useful information below in our FAQs section
£90.69
Solid Oak T&G Nosing 60x26mm - 15mm Floors
Solid oak nosing's are perfect for finishing a step or the edge of stairs. *As all of our thresholds are natural solid oak products, this means the grain and colour may vary.
£4.49 - £57.83
Bona - Mix and Fill
Bona Mix & Fill joint filler available in 1L & 5 L. Designed for mixing to a suitable consistency with fine sanding dust from the timber floor that is being treated. Bona Mix & Fill can be used to fill narrow joints up to 2mm wide and other small defects in the wood. Key features For use with all Bona finishing and oil systems Solvent free Bona Mix and Fill is low odour Fills but will not slump Conveniently waterborne, but anti-corrosive Fast drying Bona Mix and Fill may be sanded Always matches the colour of the joint
£17.23 - £65.59
Bona R848T Flexible Wood Flooring Adhesive 600ml Sausage
Bona R848T Flexible Wood Flooring Adhesive 600ml Sausage is an Elastic, 1 component silane parquet adhesive. R848T has a higher viscosity than R848. It feels thicker and has an improved initial grab, which reduces the risk of hollow spots. The adjusted formulation makes the adhesive well suitable for the installation of solid strip floors and engineered and mosaic parquet.KEY BENEFITS Easy to apply Fast initial bonding strength allows load after 24 hrs Up to two years of shelf life Higher viscosity, improved rib stability CoverageIf used with a trowel 1 sausage will cover approximately 1m2 If used as a baton system with 200mm centres between batons 1 sausage will cover approximately 1.5m2
£14.06
Solid Oak Scotia Beading 19mm - 2.44m Lengths - Pack of 5
Provides the finishing edge to wood flooring by covering expansion gaps between the floor and the wall. Pack of 5 - 2.7m lengths. Single units available in store only. *As all of our thresholds are natural solid oak products, this means the grain and colour may vary.
£4.49 - £55.72
Osmo Top Oil - 0.5L
Osmo Top Oil is ideal for protecting interior furniture surfaces and work surfaces made of solid wood or edge-glued panels (e.g. kitchen worktops, desks, shelving etc.). Also suited to cork and OSB.
£3.99 - £22.40
Lecol - 7500 Filler
Lecol 7500 Filler has been specially developed for the easy filling of joints or damaged spots in parquet or other wooden floors. The filler is mixed with fine abrasion dust from the wood in order to obtain a paste that can be used to fill small voids. Key Features: Very fast drying time Allows sanding after a short period of time Specifically developed for wooden floors Easy to use Low odour Safe to use Very good filling properties Very strong adhesion Water free
£23.09 - £79.67
Bona Gap Master - 310ml - Select Colour
Bona Gap Master is a silicon-free, acrylic-based mastic for sealing gaps towards skirting boards and thresholds. The mastic is available in 15 different colours and can be finished with all Bona lacquers when dry. Its material is permanently elastic (15 % maximum movement tolerance), and it is solvent-free and odourless. It can also be used to repair damages and fill gaps and cracks in wood floors.
£14.86
Lecol 5500 Wood Flooring Adhesive
Lecol 5500 Parquet Flooring Adhesive is solvent-based and can be used for all types of wood. It is suitable for installation on absorbent and non-absorbent sub-floors meaning that it can be universally applied. In many cases Lecol 5500 can even be used to install pre-finished parquet without any problems. Our customers consistently report first class results with Lecol 5500 and it comes highly recommended by Professionals. Key Features Lecol 5500 Parquet Adhesive is ready to use Very strong adhesion Excellent filling properties High level of initial grab Lecol 5500 can be used with underfloor heating Lecol 5500 is widely used by professional floor fitters Coverage: 0.9kg per m2 Universally applicable Economical application Available in 6kg and 16kg tin. Application with Glue Trowel
£61.10 - £121.12
Bona Mega
Bona Mega lacquer is an oxygen-crosslinking polyurethane finish, ideal for heavy domestic and light commercial timber flooring, offering superb protection against spills. Its innovative formulation has proven perfectly suited to wooden floors with high movement, planks and underfloor heating. Waterborne lacquer with high chemical resistance. Key Features 1K simplicity with 2K performance Touch dry and ready to recoat in 2.5–3.5 hours @ 20°C. Light use in 24 hours No side-bonding, ideal for underfloor heating, plank floors etc Dispersion mainly consisting of plant-based oil Excellent resistance to scuff marks and common chemicals GreenGuard approved for low indoor emissions A ready-to-use, single-part water-based floor varnish for high traffic environments Ideal for heavy domestic and light commercial floor use, Extremely durable and hard wearing Highly resistant to wear, scuff marks and scratches Offers excellent liquid and chemical resistance GreenGuard approved for low indoor emissions Low V.O. Easy and safe to apply (recommended Bona Super Coat Roller) Bona Wood Floor Primers For application to bare wood floors we recommend using one coat of Bona wood primer. Bona Primers help with adhesion between the varnish and floor and can help with the colouration of the final finish. Bona Mega is compatible with the following primers: Product Us Bona Prime UX A non-yellowing, clear primer for use with the Bona range of varnishes Bona Intense Primer A 100% polyurethane based primer for finishes requiring better adhesion Bona Amber Primer Wood primer for oak and darker tropical species of wood. Important: The use of Bona White Primer or Bona Natural Primer is not recommended for this product as the natural ingredients in Bona Mega will yellow the final finish. Preparation Previously waxed, polished or oiled floors CANNOT be over-coated with Bona Mega Varnish unless sanded back to bare wood. Floors to be lacquered must be clean, dry and free of all dust, dirt and other surface contaminates. Sand floors back to bare wood Final sanding should be done with a 100 grit sanding disk, screen or good quality sandpaper Use a vacuum cleaner to remove all traces of sanding dust from the area to be varnished For filling small gaps between walls, skirting boards and floors use Bona Gap Master For filing holes, splits, dents and other surface imperfections, use Bona Mix and Fill or Bona Mix and Fill Plus Bona mega technical data sheet
£24.00 - £93.90
Osmo UV-Protection Oil Extra 420
Osmo UV-Protection-Oil Extra is a satin, clear finish for exterior. It is based on natural oils, is microporous, and does not crack, flake, peel or blister. When used as a final finish after staining wood, Osmo UV-Protection-Oil Extra prolongs the renovation time significantly. As a stand alone finish, with two coats, it prolongs the greying process on vertical surfaces by UV-Protection factor 12 in comparison to untreated wood. The finish contains active ingredients which protect it from mould, algae and fungal attack. Easy to renew, no sanding or primer necessary. Easy to apply, will not dry during application.
£27.29 - £79.56
Osmo Maintenance Oil - 1L
Especially developed for the most demanding wooden floors treated with Osmo Polyx®-Oil for regular cleaning and occasional refreshing and maintenance. Floors with expected high tread and quick wear can be regenerated and cleaned at the same time with Maintenance Oil. Key Features Coverage - 40-60sqm A Litre Coats 1 coat Drying Time 3-4 hours (23°C/50% R.H.). Application to Small areas with A Cloth Larger areas with A Scraper / Microfibre roller, then Buffing machine Application SURFACE PREPARATION Wood surface must be clean, dry (moisture content max. 18 %) and free of dust.Osmo Maintenance Oil is ready to use. Do not thin.Stir well before use.Clean the surface thoroughly with Osmo Intensive Cleaner and rinse (damp mopping) with clear water.The finished surface is influenced by several factors, including the condition of the wood. Therefore, a trial application is always required, especially for unfamiliar surfaces. METHOD OF APPLICATION With Osmo Double Blade Scraper or Osmo Microfibre Roller, apply thinly and evenly to the clean and dry wood along the wood grain and rub into the wood with a white pad (do not rub in 3098). Remove excess product.For smaller areas, Osmo Maintenance Oil can be applied with a lint-free cloth.Allow for good ventilation while drying. NOTE The maintenance results are influenced by several factors, including the condition of wood. Therefore, a trial application is always required. If wood is raw or already greyed, the surface must be sanded and treated with Osmo Polyx®-Oil. Do not rub in Maintenance Oil 3098 Semi-Matt/Anti-Slip with a single disc machine.
£33.29 - £36.64
New Premium Bona Spray Mop for Oiled Floors
The Bona Oiled Floor Spray Mop is an effective and easy-to use spray mop for oiled wooden flooring. It comes complete with an 850ml refill cartridge containing Bona Cleaner for Oiled Floors and a machine washable microfibre cleaning pad.Dry sweep or vacuum floors before wet cleaning to ensure that any dirt and grit is removed to avoid scratches.The Bona Spray Mop for Oiled Floors comes in five sections that are easily assembled. Instructions are supplied on the box. The two handle pieces are connected by a green slide up sleeve. This is tight fitting and may require some force to click into place.
£51.53
Refina Spiked Rollers + Frame - Long Fixed Disks
Spiked rollers with fixed 40mm discs for levelling & rolling out air bubbles in epoxy & cementitious floor coatings. Supplied with a heavy duty zinc plated double arm roller frame. The frame has a 28mm diameter cuff for attaching to wooden handles. Spiked rollers complete with heavy duty frames Fixed discs 40mm Roller diameter 125mm Heavy duty zinc coated steel frames Produced by Refina in the UK Handle (sold separately) Specifications 9" (230x125mm) 12" (315x125mm) 15" (400x125mm) Application For rolling out air bubbles Levelling & moving Epoxy coatings Cementitious floor coatings & self-levellers
£30.84 - £37.39
Lecol Wood Flooring PVAC - 0.75g
Water-based Dispersion PVAC Adhesive. Lecol PVAC glue is a water-based dispersion glue which guarantees a durable adhesion. Lecol PVAC glue is a quick polyvinylacetate based glue and has a high shear strength. Lecol PVAC glue corresponds to the requirements of Class Norm EN 204. Thinner: Ready for use. (can be mixed with water). The tools can be cleaned with water, dried glue with acetone. Consumption: approx. 120 - 200 Gr/m² Open time: approx. 5 -7 minutes. The glue must dry for at least 12 hours.Storage: Do not use at a temperature below 10°C, Do not store below 5°C, Protect from frost. Shelf life approx 6 months. Application Especially suitable for glueing laminate and Engineered wood floor elements. The glue should applied at room temperature (20°C) to the groove from end to end. Press the panelstogether firmly to ensure a tight fit. Use a wooden block to prevent damage to the tongue. The open time of Lecol PVAC glue is approx 5-7 minutes, depending on the temperature.The average drying time of the glue is about 30 minutes. Excess glue should be removed immediately with a towel, before it dries. Open containers should be resealed immediately and stored correctly.
£12.13
Osmo UV-Protection Oil Tints
Please Note: Colours were developed to appear in harmony with their respective wood species e.g. 426 Larch for Larch wood projects. The wood’s natural colour and character will influence the final result. Plus, the darker the colour, the stronger the UV-resistance. Please always trial apply! All exterior woods grey into a patina colour over time, however UV-Protection Oil Tints have been developed to maintain the wood's natural colour with the use of pigments to optimally match the wood's natural characteristics. Ideal for windows, doors, cladding, fencing and other vertically structured joinery (not recommended for flat surfaces such as decking). Natural oil-based and microporous finish does not crack, flake, peel or blister. Water and dirt resistant, moisture regulating and reduces wood swelling and shrinkage. Osmo 425 Oak UV Protection Oil gives optimal protection from the sun, similar to Osmo 420 but it improves the UV resistance further by also having a small amount of Oak pigment. The oak pigment will darken the wood slightly and accentuate the wood grain but we recommend ALWAYS do a test before application, sample sachet available. For exterior use only. Especially recommended for vertical surfaces such as timber cladding, windows and doors Prolongs the renovation time significantly when used as a top coat for staining wood Contains active ingredients for the preventative protection against algae and fungal decay. Key features Coverage (m2) per Litre: 18 Base: Solvent Paint Application: Brush, Roller Suitable Substrate: Exterior Woodwork, Window Frames, Doors Exterior: Exterior Drying Time: 12 Hours PREPARATION Wood surface must be clean, dry and frost-free (moisture content max. 20%). UV-Protection-Oil Tints is ready to use. Do not thin. Stir well using a flat stirring stick or spatula before use. Ideally, surfaces are sanded no finer than a P120 grit grade of sand paper. Sanding to finer grades will reduce required absorbency.If possible, and if the wood is absorbent, please apply first coat to all sides before installation. Fresh wood containing natural wood ingredients /extractives (eg: Cedar, Teak, Mahogany or Iroko) are often less absorbent and need to weather off first before applying the product. Please refer to website ‘Suitability’ section for more details. Weathering helps ingredient rich wood become more absorbent and the wood finish adheres optimally. For renovation works, clean old microporous stains thoroughly – if necessary sand lightly. Clean and restore already greyed or weathered wood at the same time with Osmo Wood Reviver Power-Gel. Old paints and lacquers must be completely removed. As a general rule, wear a dust mask during sanding works. To maintain absorbency, avoid sanding surfaces finer than a P120 grit. Weather ingredient rich wood after sanding.The finished surface is influenced by several factors, including the condition of the wood. Therefore, a trial application is always required, especially for unfamiliar surfaces. Soft wood species like Pine or Spruce are more prone to blue stain, rot and insects. If desired, pre-treat these soft woods if possible on all sides with Osmo WR Base Coat. APPLICATION With Osmo Flat Brush or Osmo Microfibre Roller, apply thinly along the wood grain and spread well.Allow to dry for approx. 12 hours under good ventilation.Then apply the second coat.Alternatively the second coat can also be carried out with UV-Protection-Oil Extra Clear.When recoating colour treated surfaces, or for renovation works, one coat applied to the clean and dry surface is usually sufficient.
£3.99 - £88.48
Osmo Polyx Oil Rapid
Osmo Polyx-Oil Rapid 3232 and 3262 is ideal for protecting all wooden floors, such as solid wood and plankwood flooring, blockstrip, OSB and cork floors, as well as for furniture. Key Features Fast drying (apply 2 coats in a single day) Enhances the wood's natural character Extremely durable and hardwearing Very water and dirt resistant Resistant to common liquid spillages such as water, juice, tea, cola and wine Saliva-resistant and sweatproof, suitable for children's toys Microporous, breathable finish which does not crack, peel or flake No sanding necessary for spot repairs or future applications Resistant to common household spillages Application is by brush or roller Coverage up to 24sq/m per litre Dry time 4 hours and recoatable after 12 hours. Recommended 2 coats Application SURFACE PREPARATION Wood surface must be clean, dry and frost-free (moisture content max. 18%).Osmo Polyx®-Oil Rapid is ready to use. Do not thin.Stir well using a flat stirring stick or spatula before use.Clean old microporous stains thoroughly. Old paints and lacquers must be completely removed.As a general rule, wear a dust mask during sanding works. Fill small cracks, larger joints or holes in wood (with Osmo Wood Filler).Sand wood surfaces carefully. Begin with coarse sandpaper – final sanding work for flooring P120-150, for furniture P180-240. Before oiling the surface, remove sanding dust with a broom or vacuum.The finished surface is influenced by several factors, including the condition of the wood. Therefore, a trial application is always required, especially for unfamiliar surfaces. METHOD OF APPLICATION With Osmo Flat Brush, Osmo Microfibre Roller or Floor Brush, apply thinly and evenly to the clean and dry wood along the wood grain and spread well within 10-15 minutes. Wipe away any excess product.Allow to dry for approx. 4-5 hours under good ventilation. After drying, apply a second coat also thinly and quickly. Avoid covering during drying and curing. After 2-3 weeks, the surface is fully cured. When renovating or recoating an already oiled surface, one coat applied to the clean and dry surface is usually sufficient. NOTE Oils enhance the natural tone of wood (permanent wet effect). Applying the product too generously and insufficient ventilation lead to delays in drying.For dark and extractive-rich hardwoods (e.g. Wenge, Merbau, Jatoba etc.), we recommend using Osmo Wood Wax Finish Clear Extra Thin. A trial application is recommended.For cork surfaces, due to their high absorbency please ensure that the wood finish is applied especially thinly. On cork, longer drying times are to be taken into consideration (at least 6-8 hours). If a higher gloss level is desired use Osmo Liquid Wax Cleaner very thinly and polish when dry. Avoid using Osmo Liquid Wax Cleaner on surfaces that have not dried and cured properly. Always trial apply first. Using general or multi-purpose cleaners will increase the frequency of maintenance and recoating. Allow finish to fully cure before heavy usage. CARE Regular Cleaning: Wood surfaces treated with Polyx®-Oil Rapid are highly repellent and easy to maintain. Remove debris with the Osmo green Dust-Mop from the Mop Cleaning Kit for Floors, or use a broom or a vacuum cleaner.Damp mop floors using diluted Osmo Wash and Care and the Osmo Micro-Mop Plush from the Mop Cleaning Kit for Floors. Avoid saturating the surface with water. For the convenient cleaning of floors use Osmo Spray-Mop. For furniture or small areas, use Osmo Spray Cleaner and Osmo Easy Pads. Occasional Maintenance: For spot cleaning stubborn scuff marks, or occasionally refreshing satin or gloss Polyx-Oils use Osmo Liquid Wax Cleaner. Alternatively, Osmo Maintenance Oils can be used to occasionally refresh most Polyx Oil sheen levels, including matt. Ensure surfaces are appropriately cleaned before thinly applying Osmo Maintenance Oils. Recoating: Simply re-apply one coat onto the appropriately cleaned and dried surface when signs of wear become visible.
£3.99 - £106.58
Osmo Cleaning Kit (Successor of Osmo Opti-Set) Wood Floor Cleaning Mop Set
For cleaning and maintaining wooden, vinyl, tiled, and natural stone flooring. Easily attaches to Osmo System Telescopic Handle for back-preserving length adjustment. A dash of Osmo Wash and Care in mop water removes everyday dirt exceptionally with Micro-Mop Plush. Active-fibre cloth Eventually, flooring needs to be refreshed. With Liquid Wax Cleaner the surface is regenerated and cleaned at the same time with Active-Fibre Cloth. Telescopic pole has a high quality aluminium telescopic handle with SoftTouch grip to work safely. Simply connects to the joint for a secure fitting and effective cleaning. Pole is adjustable in length from 120-200 cm and is also suitable for use with many other tools from Osmo. Kit Includes Dust-Mop for dry cleaning Micro-Mop for damp-cleaning with Osmo Wash and Care Active-Fibre Cloth for intensive cleaning and refreshing with Osmo Liquid Wax Cleaner Telescopic pole (adjustable in length from 120-200 cm) Quick fix mop head Applications DUST REMOVAL To remove loose dirt, we recommend dry cleaning with Osmo Dust-Mop, a conventional vacuum cleaner or broom. DAMP MOPPING Prepare a dilution of Osmo Wash and Care with water in a suitable bucket (Dilution 15 mL Wash and Care per 2 litres water). Soak the Micro-Mop Plush cloth head then wring out well. Only damp mop the floor to reduce water logging. Regular cleaning will ensure the process remains very easy
£60.67
Bona Wood Floor Cleaning Kit
Bona Wood Floor Cleaning Kit, new parent, new home or new floors, the Bona Wood Floor Cleaning Kit is just what you need. Its rinse-free, streak-free formula cleans hard-surface floors effectively by removing dust, dirt and grime safely. The ready-to-use pH-neutral formula dries quickly and cleans wood floors by gently and effectively removing dust, dirt and grime to reveal the floor's natural shine and beauty. Water-based solutions and Greenguard Gold Certification* ensure a safe product for you - and our planet. In other words, it has everything you need for the safe and easy cleaning of your wood floors!Kit includes:1L Spray - Bona Wood Floor Cleaner for streak-free, beautifully clean floors.Durable telescopic 4-piece mop with handle and large mop head for quick and easy cleaning.Extra-large patented Bona Microfiber Cleaning Pad that removes 99% of bacteria* and are machine washable up to 500 times.*Accredited Bacterial Removal Testing Removes 99% of E. coli and Listeria from wood or LVT flooring when using the Bona Microfiber Cleaning Pad with Bona Wood Floor Cleaner, Bona Hard-Surface Floor Cleaner, Bona OxyPower Floor Deep Cleaners or water; Tested at an independent accredited lab in 2020. White oak wood floor and luxury vinyl floor panels were tested in multiple replicates along with various bacteria. The floor panels were then cleaned and rated for bacteria removal with a Bona Microfiber Mop and Bona Microfiber Pad, along with multiple Bona cleaners.
£27.41
Bona MicroFibre Cleaning Pad
The Bona Microfibre Cleaning Pad is designed for effective cleaning with Bona Floor Cleaners, and a smooth application of Bona Floor Polish.Conventional cleaning pads can push and scatter dust and dirt, leaving residue behind. The Bona Microfibre Cleaning Pad features a unique design with dual-zone cleaning action. The dark blue outer fibres break up grime, while the light blue inner fibres trap and absorb dirt with more absorbency than with our previous pad. It is designed for effective cleaning, and can also be used for a smooth application of Bona polish. For best results, use a designated pad for polish application.
£10.83
Solid Oak T&G Nosing 82x28mm - 20mm Floors
Solid oak nosing's are perfect for finishing a step or the edge of stairs. *As all of our thresholds are natural solid oak products, this means the grain and colour may vary.
£4.49 - £76.55
Osmo Polyx Oil Effect- Raw Matt (3044)
Osmo Polyx-Oil Effect Raw is suitable for the protection and nearly invisible finish of all light-coloured interior woods, such as wooden floors and furniture. Key Features Nearly invisible appearance, no 'permanent wet effect' Light coloured wood stays light coloured Extremely durable and hardwearing Very water and dirt resistant Resistant to common liquid spillages such as water, juice, tea, cola and wine Saliva-resistant and sweatproof, suitable for children's toys Microporous, breathable finish which does not crack, peel or flake No sanding necessary for spot repairs or future applications Application SURFACE PREPARATION Wood surface must be clean, dry and frost-free (moisture content max. 18%).Osmo Polyx®-Oil Effect Raw is ready to use. Do not thin. Stir well using a flat stirring stick or spatula before use.Clean old microporous stains thoroughly. Old paints and lacquers must be completely removed. As a general rule, wear a dust mask during sanding works.Fill small cracks, larger joints or holes in wood (with Osmo Wood Filler).Sand wood surfaces carefully. Begin with coarse sandpaper – final sanding work for flooring P120-150, for furniture P180-240. Before oiling the surface, remove sanding dust with a soft brush or vacuum cleaner. Applying Polyx®-Oil Effect Raw over very textured or coarse surfaces could appear more white. The finished surface is influenced by several factors, including the condition of the wood. Therefore, a trial application is always required, especially for unfamiliar surfaces. METHOD OF APPLICATION With Osmo Flat Brush, Floor Brush or Osmo Microfibre Roller, apply thinly along the wood grain and spread well. Applying excess Polyx®-Oil Effect Raw 3044 may lead to a white chalky surface. Remove visible white pigments before allowing the surface to dry. Allow to dry for approx. 24 hours under good ventilation.After drying, quickly apply a second coat also thinly.When renovating or recoating an already oiled surface, one coat applied to the clean and dry surface is usually sufficient. NOTE Polyx®-Oil Effect Raw is slightly white tinted and protects lighter coloured wood species nearly invisibly. On dark, reddish or ‘smoked / fumed’ wood species, Polyx®-Oil Effect Raw is visible as slightly white chalky surface. Applying excess Polyx®-Oil Effect Raw 3044 may also lead to a white chalky surface. Remove visible white pigments before allowing the surface to dry.A trial application is recommended. Applying the product too generously and insufficient ventilation lead to delays in drying time and the typical smell of oil.Any brushstrokes can be removed with an unused dry Microfibre Roller within 30 minutes after applying. For extractive rich hardwoods (e.g. Wenge, Merbau, Jatoba etc.), we recommend using Osmo Wood Wax Finish Clear Extra Thin. A trial application is recommended.Caution: Apply max. one coat thinly to cabinet interiors and drawers with a cloth. Using general or multi-purpose cleaners will increase the frequency of maintenance and recoating. Allow finish to fully cure before heavy usage. CARE Regular Cleaning: Dust mopping using the green Dust-Mop from the Osmo Mop Cleaning Kit for Floors. Damp mopping using diluted Osmo Wash and Care and the Micro-Mop plush from the Osmo Mop Cleaning Kit for Floors. Alternatively use the convenient Osmo Spray-Mop. Occasional Maintenance: If the oiled surface remains light in colour yet there is a reduction in water repellency, refresh the surface with Osmo Maintenance Oil 3079 Clear Matt. Before using Osmo Maintenance Oil 3079, damp clean the surface using diluted Osmo Wash and Care, or alternatively Osmo Spray cleaner and allow to fully dry. For small areas Osmo Maintenance Oil 3079 can be applied thinly with a lint free cloth or white pad. Remove excess product. Allow for good ventilation while drying. A small trial is highly recommended first. Recoating: When slight signs of wear become visible, and providing the surface does not become completely bare, simply re-apply one thin coat onto the clean and dry surface. Avoid applying Polyx®-Oil Effect Raw to bare wood surfaces that have become dirty. Bare, dirty surfaces could appear more rich and dark following the application of the oil finish. A small trial is highly recommended first.
£3.99 - £98.60
Bona Prime Natural 5L
Bona Natural Primer is a coloured waterborne primer for untreated wood floors designed to give an untreated, raw wood look. It can be applied in one or two coats to achieve the desired appearance. Highly forgiving formulation designed for easy roller application. To enhance the untreated appearance combine Bona Natural Primer with Traffic HD Raw, Traffic HD Extra Matt or Bona Mega ONE Extra Matt. Key Benefits Light, untreated wood look Easy roller application GreenGuard certified for low indoor air emissions Dry time 2-3 hours (20°C/60% R.H) Coverage upto 12sq/m per litre Technical Datasheet download.PDF
£95.56
Floor Protectors - Felt Pads/Furniture Feet
Protect your flooring from scratches and scrapes with the assortment of 42 felt pads. The pads should be placed on all furniture which comes into contact with the flooring to prolong the life of your flooring. The pack contains: 2 x Rectangle Pads = 150 x 110mm 8 x Rectangle Pads = 48 x 32mm 16 x Disk Pads = 25mm Diameter 16 x Disk Pads = 9mm Diameter
£4.99
Pipe Ferrules (Dowelled) 17x50mm - 2 Pack
Solid oak wood pipe ferrule. 2 Pack. *As all of our thresholds are natural solid oak products, this means the grain and colour may vary.
£9.00
Osmo Door Oil 1L
Osmo Door Oil is ideal for veneered doors. The unique formulation penetrates the wood surface which remains microporous and whilst the finish will not crack, peel, flake or blister. The surface also becomes healthy and elastic, and the wood's fibres are prevented from becoming dry and brittle over time as well as shrinking and swelling. Application SURFACE PREPARATION Wood surface must be clean, dry and frost-free (moisture content max. 18%). Osmo Door-Oil is ready to use. Do not thin. Shake well before use. For solid doors, clean old microporous stains thoroughly. Old paints,varnishes and lacquers must be completely removed. If renovating veneered doors, always check with the door manufacture that renovation is possible. Always wear a dust mask while sanding. Fill small cracks, larger joints or holes in wood (with Osmo Wood Filler). Sand wood surfaces carefully. Begin with coarse sandpaper – final sanding P120-150 for solid wood doors. Before oiling the surface, remove sanding dust with a soft brush or vacuum cleaner. If possible, please apply the first coat to all sides before installation. METHOD OF APPLICATION With Osmo Flat Brush or Osmo Microfibre Roller, apply thinly and evenly to the clean and dry wood along the wood grain and spread well. If applying the Door-Oil 3033 Raw, remove excess white pigment before allowing the surface to dry. Allow for good ventilation while drying. After drying, apply a second coat – also thinly. NOTE Applying the product too generously and insufficient ventilation lead to delays in drying time. Oils enhance the natural tone of wood (clear Door-Oil 3060 with permanent wetlook-effect). Osmo Door-Oil 3033 Raw counteracts exactly this effect and protects lighter coloured wood almost invisibly. The original look of the wood can be kept – no emphasising of the natural colour of the wood (no wetlook-effect). On dark/reddish wood species, Osmo Door-Oil 3033 Raw can be seen as a faintly white surface. Over application of Osmo Door-Oil 3033 Raw can also result in a faintly white surface. A trial application is recommended. Using general or multi-purpose cleaners will increase the frequency of maintenance and recoating. Allow finish to fully cure before heavy usage. CARE Regular Cleaning: Dust mopping. Damp mopping using Osmo Spray-Cleaner. Occasional Maintenance: For the Intensive cleaning of stubborn scuff marks, and refreshing the sheen on Osmo Door Oil 3060 clear satin, use clear Osmo Liquid Wax Cleaner. Avoid using Liquid Wax Cleaner over Osmo Door-Oil 3033 Raw matt as it will appear more shiny. Recoating: Simply re-apply one coat onto the clean and dry surface when slight signs of wear become visible.
£38.08
Cork Expansion Strip (10 Pack)
Cork expansion strip comes in 91cm (3 feet) long and available in different sizes. 8mm x 12mm 10mm x 10mm 10mm x 14mm 12mm x 22mm
£15.82 - £24.84
Carpet to Carpet - Solid Oak
Our carpet to carpet threshold is used in door ways that have carpets in both joining rooms. *As all of our thresholds are natural solid oak products, this means the grain and colour may vary.
£4.49 - £39.74
Osmo Repair Kit
The Osmo Repair Kit can be used for making good any cracks, scratches and dents in all exterior and interior wooden surfaces. The included wax sticks are made from a blend of mineral waxes, coloured with earth and oxide dyes. Key Features For repairing scratches, dents, cracks and splits in exterior and interior wooden surfaces Suitable for solid wood, veneer, foil, thermosetting, thermoplastic & plastic surfaces Wax sticks can be mixed during melting to produce unique shades for repairs Good elasticity meaning no development of cracks Quick and easy to use. Kit Contains 6 x 8gm wax filler sticks of various colours Heat pen Batteries X 2 For an alternative interior wood filler, why not try Osmo Interior Wood Filler or Osmo Interior Gap Sealer For extra wax sticks, use Osmo Wax Stick Refill Pack Application Always do a test area before starting any project to assess product suitability and final finish. Follow the manufacturer's instructions on the container at all times.Liquify the wax filler stick or sticks with the heated melting knife and drop the melted wax filler into the damaged area until the scratch, hole or imperfection in the wood is slightly overfilled.When the wax filler has dried, use the grooved handle of the melting tool to plane the repaired area, removing any excess surface waxTo restore the grain pattern of the filled area, scratch the surface of the repair area lightly with a pointed item, then re-fill with the grain shade of waxRemove any final filler residues by polishing lightly with the grey finishing pad included within the Osmo Repair KitPlease note: The clear wax filler stick can be used to fill pressure indentations in the timber.
£22.27
Bona Refill Cartridge for Oiled Floors 850ml
Bona Cleaner for Oiled Floors is an easy, safe and effective cleaner for oiled wooden floors that simultaneously cleans and nourishes the oiled finish for increased protection. This handy refill cartridge is for use with the Bona Oiled Floor Spray Mop or any of the other Bona Spray Mops. Can be easily topped up with Bona Cleaner Refill for Oiled Floors.
£15.60
Ball Stopgap 1200 Pro Screed - Bag 20kg Including 5L Liquid
F Ball Stopgap 1200 Pro Bag & Bottle 20kg. F Ball Stopgap 1200 Powder Mixed with Liquid is a low odour, fast setting, fast drying, two component smoothing underlayment suitable for preparing sound internal subfloors prior to the installation of new floor coverings. It is particularly suitable for use over old adhesive residues (including bitumen and carpet tile tackifiers) without the need for priming. STOPGAP 1200 can be used for patch filling timber floors prior to overlaying with plywood. It is suitable for use in clinical and biologically sensitive areas, clean rooms etc. STOPGAP 1200 mixed with STOPGAP 1200 Liquid has been tested in accordance with IMO 2010 FTPC Part 5 (IMO Res. MSC 307(88)) and Annex 2 item 2.2 and approved for use in marine application by DNV. Suitable direct to adhesive residues, carpet tile tackifier and waterproof surface membranes Lay floor coverings from 4 hours Application thickness from 2 - 10mm Can be filled up to 30mm Fast setting Protein Free Excellent self levelling properties Suitable for use in clinical areas Approx coverage of 1.98kg/m²
£34.00
Hand Pad Holder and Accessories
The hand pad holder is for attaching to the Osmo Oil Finish Application Fleece Can also be used with the red, green and white Superpad. It Aids with control and precision Suitable for DIY and professional use Measures 85 x 135mm. Applications Superpads are a rectangular size of 95 x 155 mm, ideal for manual processing in combination with Osmo Hand Pad Holder. For the best results and protection of kitchen worktops and dining furniture, apply the first coat of Osmo TopOil with the Osmo Flat Brush and leave to dry before applying a final coat using the application fleece with Hand Pad Holder. It is not recommended to use the Application Fleece when applying Wood Protector or Wood Wax Finish Clear Extra Thin due to the lower viscosity of these particular products. To maintain the wood’s protection, apply Osmo Liquid Wax Cleaner using the white pad with Hand Pad Holder. To remove tough stains and dirt, depending on the extent of the dirt use red pad in combination with Hand Pad Holder. Can be used for smaller areas or for edges and corners that cannot be reached by machines, approx. 1 m² per side. Additional Information: Hand Pad Holder size: 85 x 135 mm Rectangular pad sizes: 95 x 155 mm
£4.52 - £9.14
Bona Quantum Wood Flooring Adhesive 15kg Tub
A hard-elastic, 1-component silane wood flooring adhesive. A true all rounder suitable for practically all types of wood flooring and subfloors, in particular solid and wide engineered wood floors. Its hard-elastic properties make it strong and resistant against movement of wood while relieving tension on the sub floor. Key Benefits Fast initial bonding strength allows load after 24 hours Up to two years' shelf life Great rib stability Can be used on outdoor decks Direct use on tiles and metal Compatible with underfloor heating Coverage dependant on trowel size : 850 - 1500g/m2 Product Advantages Adhesive hardens due to a chemical reaction with moisture. Technical Spec Open time: Approx 40mins* Drying time, until: - Application of load: 24-48hrs Under normal climate conditions, 20°C/60% R.H. Note: Please also refer to the instructions for use provided by the parquet manufacturer. Application Before using the adhesive the following climatic conditions must be met: Air temperature: min. 18°C Floor temperature: min. 15°C (with underfloor heating max. 20°C) R.H: max. 70 %- The adhesive itself must, if necessary, be brought to the right temperature. Apply with a or notched trowel
£117.67
Refina Wooden Handle
Wooden handles with a diameter of 28mm for the spiked rollers, pin levellers, notched levellers & skid levellers. Available in 5ft (150cm) or 6ft (180cm) lengths. Specifications 5ft (1500mm) 6ft (1800mm)
£17.32 - £20.59