Hard Wax Oils (interior)

Osmo Polyx-Oil Original 3032 and 3062 is a protective wood treatment for interior use. Combines natural oils and waxes to form a hardwearing and durable finish which is ideal for wooden flooring and furniture.  Osmo Polyx Hardwax Oil provides a warm and rich effect that brings out the true beauty of all woods by emphasising the grain and promoting its natural characteristics. Exceptional durability is achieved. Microporous and will not crack, flake or peel.              Key Features Resistant to common household spillages Application is by brush or roller  Coverage up to 24sq/m per litre Touch dry between 4-8 hours and recoatable after 12 hours. Recommended 2 coats Application  SURFACE PREPARATION Wood surface must be clean, dry and frost-free (moisture content max. 18%).Osmo Polyx®-Oil Original is ready to use. Do not thin. Stir well using a flat stirring stick or spatula before use. Clean old microporous stains thoroughly. Old paints and lacquers must be completely removed. As a general rule, wear a dust mask during sanding works. Fill small cracks, larger joints or holes in wood (with Osmo Wood Filler).Sand wood surfaces carefully. Begin with coarse sandpaper – final sanding work for flooring P120-150, for furniture P180-240. Before oiling the surface, remove sanding dust with a broom or vacuum.The finished surface is influenced by several factors, including the condition of the wood. Therefore, a trial application is always required, especially for unfamiliar surfaces. METHOD OF APPLICATION With Osmo Flat Brush, Floor Brush, Oil Finish Applicator Fleece (Hand Pad Holder) or Osmo Microfibre Roller, apply thinly along the wood grain and spread well. Allow to dry for approx. 8-10 hours under good ventilation.After drying, quickly apply a second coat also thinly. After 2-3 weeks, the surface is fully cured. When renovating or recoating an already oiled surface, one coat applied to the clean and dry surface is usually sufficient. NOTE Oils enhance the natural tone of wood (permanent wet effect). Applying the product too generously and insufficient ventilation lead to delays in drying.For dark and extractive-rich hardwoods (e.g. Wenge, Merbau, Jatoba etc.), we recommend using Osmo Wood Wax Finish Clear Extra Thin. A trial application is recommended.For cork surfaces, due to their high absorbency please ensure that the wood finish is applied especially thinly.On cork, longer drying times are to be taken into consideration (at least 24 hours).Caution: Apply max. one coat thinly to cabinet interiors and drawers with a cloth. If a higher gloss level is desired use Osmo Liquid Wax Cleaner very thinly and polish when dry. Avoid using Osmo Liquid Wax Cleaner on surfaces that have not dried and cured properly. Always trial apply first. Using general or multi-purpose cleaners will increase the frequency of maintenance and recoating. Allow finish to fully cure before heavy usage. CARE Regular Cleaning: Wood surfaces treated with Polyx®-Oil are highly repellent and easy to maintain. Remove debris with the Osmo green Dust-Mop from the Mop Cleaning Kit for Floors, or use a broom or a vacuum cleaner.Damp mop floors using diluted Osmo Wash and Care and the Osmo Micro-Mop Plush from the Mop Cleaning Kit for Floors. Avoid saturating the surface with water. For the convenient cleaning of floors use Osmo Spray-Mop. For furniture or small areas, use Osmo Spray Cleaner and Osmo Easy Pads. Occasional Maintenance: For spot cleaning stubborn scuff marks, or occasionally refreshing satin or gloss Polyx-Oils use Osmo Liquid Wax Cleaner. Alternatively, Osmo Maintenance Oils can be used to occasionally refresh most Polyx Oil sheen levels, including matt. Ensure surfaces are appropriately cleaned before thinly applying Osmo Maintenance Oils. Recoating: Simply re-apply one coat onto the appropriately cleaned and dried surface when signs of wear become visible.

Read more less

Osmo Polyx-Oil Rapid 3232 and 3262 is ideal for protecting all wooden floors, such as solid wood and plankwood flooring, blockstrip, OSB and cork floors, as well as for furniture. Key Features  Fast drying (apply 2 coats in a single day) Enhances the wood's natural character Extremely durable and hardwearing Very water and dirt resistant Resistant to common liquid spillages such as water, juice, tea, cola and wine Saliva-resistant and sweatproof, suitable for children's toys Microporous, breathable finish which does not crack, peel or flake No sanding necessary for spot repairs or future applications Resistant to common household spillages Application is by brush or roller Coverage up to 24sq/m per litre Dry time 4 hours and recoatable after 12 hours. Recommended 2 coats Application  SURFACE PREPARATION Wood surface must be clean, dry and frost-free (moisture content max. 18%).Osmo Polyx®-Oil Rapid is ready to use. Do not thin.Stir well using a flat stirring stick or spatula before use.Clean old microporous stains thoroughly. Old paints and lacquers must be completely removed.As a general rule, wear a dust mask during sanding works. Fill small cracks, larger joints or holes in wood (with Osmo Wood Filler).Sand wood surfaces carefully. Begin with coarse sandpaper – final sanding work for flooring P120-150, for furniture P180-240. Before oiling the surface, remove sanding dust with a broom or vacuum.The finished surface is influenced by several factors, including the condition of the wood. Therefore, a trial application is always required, especially for unfamiliar surfaces. METHOD OF APPLICATION With Osmo Flat Brush, Osmo Microfibre Roller or Floor Brush, apply thinly and evenly to the clean and dry wood along the wood grain and spread well within 10-15 minutes. Wipe away any excess product.Allow to dry for approx. 4-5 hours under good ventilation. After drying, apply a second coat also thinly and quickly. Avoid covering during drying and curing. After 2-3 weeks, the surface is fully cured. When renovating or recoating an already oiled surface, one coat applied to the clean and dry surface is usually sufficient. NOTE Oils enhance the natural tone of wood (permanent wet effect). Applying the product too generously and insufficient ventilation lead to delays in drying.For dark and extractive-rich hardwoods (e.g. Wenge, Merbau, Jatoba etc.), we recommend using Osmo Wood Wax Finish Clear Extra Thin. A trial application is recommended.For cork surfaces, due to their high absorbency please ensure that the wood finish is applied especially thinly. On cork, longer drying times are to be taken into consideration (at least 6-8 hours). If a higher gloss level is desired use Osmo Liquid Wax Cleaner very thinly and polish when dry. Avoid using Osmo Liquid Wax Cleaner on surfaces that have not dried and cured properly. Always trial apply first. Using general or multi-purpose cleaners will increase the frequency of maintenance and recoating. Allow finish to fully cure before heavy usage. CARE Regular Cleaning: Wood surfaces treated with Polyx®-Oil Rapid are highly repellent and easy to maintain. Remove debris with the Osmo green Dust-Mop from the Mop Cleaning Kit for Floors, or use a broom or a vacuum cleaner.Damp mop floors using diluted Osmo Wash and Care and the Osmo Micro-Mop Plush from the Mop Cleaning Kit for Floors. Avoid saturating the surface with water. For the convenient cleaning of floors use Osmo Spray-Mop. For furniture or small areas, use Osmo Spray Cleaner and Osmo Easy Pads. Occasional Maintenance: For spot cleaning stubborn scuff marks, or occasionally refreshing satin or gloss Polyx-Oils use Osmo Liquid Wax Cleaner. Alternatively, Osmo Maintenance Oils can be used to occasionally refresh most Polyx Oil sheen levels, including matt. Ensure surfaces are appropriately cleaned before thinly applying Osmo Maintenance Oils. Recoating: Simply re-apply one coat onto the appropriately cleaned and dried surface when signs of wear become visible.

Read more less

Osmo Top Oil is ideal for protecting interior furniture surfaces and work surfaces made of solid wood or edge-glued panels (e.g. kitchen worktops, desks, shelving etc.). Also suited to cork and OSB.

Read more less

Osmo Polyx-Oil Effect Raw is suitable for the protection and nearly invisible finish of all light-coloured interior woods, such as wooden floors and furniture. Key Features  Nearly invisible appearance, no 'permanent wet effect' Light coloured wood stays light coloured Extremely durable and hardwearing Very water and dirt resistant Resistant to common liquid spillages such as water, juice, tea, cola and wine Saliva-resistant and sweatproof, suitable for children's toys Microporous, breathable finish which does not crack, peel or flake No sanding necessary for spot repairs or future applications Application   SURFACE PREPARATION Wood surface must be clean, dry and frost-free (moisture content max. 18%).Osmo Polyx®-Oil Effect Raw is ready to use. Do not thin. Stir well using a flat stirring stick or spatula before use.Clean old microporous stains thoroughly. Old paints and lacquers must be completely removed. As a general rule, wear a dust mask during sanding works.Fill small cracks, larger joints or holes in wood (with Osmo Wood Filler).Sand wood surfaces carefully. Begin with coarse sandpaper – final sanding work for flooring P120-150, for furniture P180-240. Before oiling the surface, remove sanding dust with a soft brush or vacuum cleaner. Applying Polyx®-Oil Effect Raw over very textured or coarse surfaces could appear more white. The finished surface is influenced by several factors, including the condition of the wood. Therefore, a trial application is always required, especially for unfamiliar surfaces. METHOD OF APPLICATION With Osmo Flat Brush, Floor Brush or Osmo Microfibre Roller, apply thinly along the wood grain and spread well. Applying excess Polyx®-Oil Effect Raw 3044 may lead to a white chalky surface. Remove visible white pigments before allowing the surface to dry. Allow to dry for approx. 24 hours under good ventilation.After drying, quickly apply a second coat also thinly.When renovating or recoating an already oiled surface, one coat applied to the clean and dry surface is usually sufficient. NOTE Polyx®-Oil Effect Raw is slightly white tinted and protects lighter coloured wood species nearly invisibly. On dark, reddish or ‘smoked / fumed’ wood species, Polyx®-Oil Effect Raw is visible as slightly white chalky surface. Applying excess Polyx®-Oil Effect Raw 3044 may also lead to a white chalky surface. Remove visible white pigments before allowing the surface to dry.A trial application is recommended. Applying the product too generously and insufficient ventilation lead to delays in drying time and the typical smell of oil.Any brushstrokes can be removed with an unused dry Microfibre Roller within 30 minutes after applying. For extractive rich hardwoods (e.g. Wenge, Merbau, Jatoba etc.), we recommend using Osmo Wood Wax Finish Clear Extra Thin. A trial application is recommended.Caution: Apply max. one coat thinly to cabinet interiors and drawers with a cloth. Using general or multi-purpose cleaners will increase the frequency of maintenance and recoating. Allow finish to fully cure before heavy usage. CARE Regular Cleaning: Dust mopping using the green Dust-Mop from the Osmo Mop Cleaning Kit for Floors. Damp mopping using diluted Osmo Wash and Care and the Micro-Mop plush from the Osmo Mop Cleaning Kit for Floors. Alternatively use the convenient Osmo Spray-Mop. Occasional Maintenance: If the oiled surface remains light in colour yet there is a reduction in water repellency, refresh the surface with Osmo Maintenance Oil 3079 Clear Matt. Before using Osmo Maintenance Oil 3079, damp clean the surface using diluted Osmo Wash and Care, or alternatively Osmo Spray cleaner and allow to fully dry. For small areas Osmo Maintenance Oil 3079 can be applied thinly with a lint free cloth or white pad. Remove excess product. Allow for good ventilation while drying. A small trial is highly recommended first. Recoating: When slight signs of wear become visible, and providing the surface does not become completely bare, simply re-apply one thin coat onto the clean and dry surface. Avoid applying Polyx®-Oil Effect Raw to bare wood surfaces that have become dirty. Bare, dirty surfaces could appear more rich and dark following the application of the oil finish. A small trial is highly recommended first.

Read more less

Osmo Polyx Oil Tint is a professional-grade wood finish that enhances the natural beauty of your wood surfaces. This oil-based formula is easy to apply and provides long-lasting protection against wear and tear. It's perfect for use on a variety of wood types, including oak, pine, and mahogany, and can be used on both indoor and outdoor surfaces. One of the unique features of Osmo Polyx Oil Tint is its wide range of available colours. The oil is also water-resistant and resistant to heat and , making it ideal for use in high-traffic areas.  Protects and colours with wood grain visible. Harmonious appearance Resistant to common liquid spillages such as water, juice, tea, cola and wine Saliva-resistant and sweatproof, suitable for children’s toys Microporous, breathable finish which does not crack, peel or flake No sanding necessary for spot repairs or future applications Key Features FINISHES - White, Light Grey, Honey, Amber, Terra, Graphite, Black (all Satin) WATER POP- spray or damp cloth timber surface, allow to dry prior to applying tints to intensify colour APPLICATION TOOLS - Osmo Flat Brush, Floor Brush, Hand Pad or Osmo Microfibre Roller RECOMMENDED USE - Interior wooden floors and furniture RECOAT - One coat, when signs of wear become visible SIZES - 5ml, 125ml, 750ml, 2.5L DRY TIME - 24 hours CLEAN UP - Osmo Brush Cleaner COVERAGE - 30m²/L with one coat COATS - 1-2 coats CARE - Osmo Wash and Care, or Spray-Mop Application Transparent colour: With Osmo Flat Brush, Osmo Microfibre Roller, Oil Finish Applicator Fleece (Hand Pad Holder) or Floor Brush, apply thinly and evenly to the clean and dry wood along the wood grain and spread well.Allow to dry for approx. 24 hours under good ventilation. If a stronger colour intensity is desired, repeat the process (however maximal two coats). Lightly stained effect: Within 20 minutes after application, wipe away product along the wood grain with a cloth or white pad. Allow to dry for approx. 24 hours under good ventilation. Intensive colour: For this application, we recommend Osmo Wood Wax Finish or Osmo Oil Stain. Important: Apply maximum one coat of Polyx®-Oil Tints or Oil Stain to flooring.(Not applicable for Polyx®-Oil Tints 3040 White, see Notes.) After thoroughly drying, a top coat with a clear Osmo Polyx®-Oil is to be carried out. Avoid covering during drying and curing. After 2-3 weeks, the surface is fully cured.

Read more less

Bona Hard Wax Oil produces the warm look of an oiled floor, and establishes a hardwearing surface that is spot-repairable and easy to maintain. It is highly suitable for floors with underfloor heating, and reliably reduces the risk of side-bonding. For enhanced protection, apply two coats. KEY BENEFITS Water and dirt repellent. Wear and scuff resistant. Safe for application on children's toys. Free from cobalt and ketoximes. Technical  Base: Modified vegetable oils & waxes Category Hardening oil, 1-comp Drying time (until use)24 h Application tools: Roller, brush or stainless steel trowel Coverage: up to 20 m²/lit

Read more less

Especially developed for the most demanding wooden floors treated with Osmo Polyx®-Oil for regular cleaning and occasional refreshing and maintenance. Floors with expected high tread and quick wear can be regenerated and cleaned at the same time with Maintenance Oil. Key Features  Coverage - 40-60sqm A Litre Coats 1 coat Drying Time 3-4 hours (23°C/50% R.H.). Application to Small areas with A Cloth Larger areas with A Scraper / Microfibre roller, then Buffing machine Application SURFACE PREPARATION Wood surface must be clean, dry (moisture content max. 18 %) and free of dust.Osmo Maintenance Oil is ready to use. Do not thin.Stir well before use.Clean the surface thoroughly with Osmo Intensive Cleaner and rinse (damp mopping) with clear water.The finished surface is influenced by several factors, including the condition of the wood. Therefore, a trial application is always required, especially for unfamiliar surfaces. METHOD OF APPLICATION With Osmo Double Blade Scraper or Osmo Microfibre Roller, apply thinly and evenly to the clean and dry wood along the wood grain and rub into the wood with a white pad (do not rub in 3098). Remove excess product.For smaller areas, Osmo Maintenance Oil can be applied with a lint-free cloth.Allow for good ventilation while drying. NOTE The maintenance results are influenced by several factors, including the condition of wood. Therefore, a trial application is always required. If wood is raw or already greyed, the surface must be sanded and treated with Osmo Polyx®-Oil. Do not rub in Maintenance Oil 3098 Semi-Matt/Anti-Slip with a single disc machine.

Read more less

Osmo Door Oil is ideal for veneered doors. The unique formulation penetrates the wood surface which remains microporous and whilst the finish will not crack, peel, flake or blister. The surface also becomes healthy and elastic, and the wood's fibres are prevented from becoming dry and brittle over time as well as shrinking and swelling. Application SURFACE PREPARATION Wood surface must be clean, dry and frost-free (moisture content max. 18%). Osmo Door-Oil is ready to use. Do not thin. Shake well before use. For solid doors, clean old microporous stains thoroughly. Old paints,varnishes and lacquers must be completely removed. If renovating veneered doors, always check with the door manufacture that renovation is possible. Always wear a dust mask while sanding. Fill small cracks, larger joints or holes in wood (with Osmo Wood Filler). Sand wood surfaces carefully. Begin with coarse sandpaper – final sanding P120-150 for solid wood doors. Before oiling the surface, remove sanding dust with a soft brush or vacuum cleaner. If possible, please apply the first coat to all sides before installation. METHOD OF APPLICATION With Osmo Flat Brush or Osmo Microfibre Roller, apply thinly and evenly to the clean and dry wood along the wood grain and spread well. If applying the Door-Oil 3033 Raw, remove excess white pigment before allowing the surface to dry. Allow for good ventilation while drying. After drying, apply a second coat – also thinly. NOTE Applying the product too generously and insufficient ventilation lead to delays in drying time. Oils enhance the natural tone of wood (clear Door-Oil 3060 with permanent wetlook-effect). Osmo Door-Oil 3033 Raw counteracts exactly this effect and protects lighter coloured wood almost invisibly. The original look of the wood can be kept – no emphasising of the natural colour of the wood (no wetlook-effect). On dark/reddish wood species, Osmo Door-Oil 3033 Raw can be seen as a faintly white surface. Over application of Osmo Door-Oil 3033 Raw can also result in a faintly white surface. A trial application is recommended. Using general or multi-purpose cleaners will increase the frequency of maintenance and recoating. Allow finish to fully cure before heavy usage. CARE Regular Cleaning: Dust mopping. Damp mopping using Osmo Spray-Cleaner. Occasional Maintenance: For the Intensive cleaning of stubborn scuff marks, and refreshing the sheen on Osmo Door Oil 3060 clear satin, use clear Osmo Liquid Wax Cleaner. Avoid using Liquid Wax Cleaner over Osmo Door-Oil 3033 Raw matt as it will appear more shiny. Recoating: Simply re-apply one coat onto the clean and dry surface when slight signs of wear become visible.

Read more less